I added some swear words as contact names, this is one way to get around the fucking censorship

At least one cat 6 ethernet in each room. Multiple outlets in any media room. One of my old houses had speaker jacks in each corner of the room which was a godsend when setting up surround sound for a home cinema setup.

Here’s a Piped link to the video in the article:

https://piped.video/watch?v=83ShvgtyFAg

I guess I’ve been looking at it wrong the whole time! Although, living in the countryside would be preferable for moustache-rainwater

I appreciate the usefulness of my eyebrows to divert rain away from my eyes. I do not appreciate my moustache’s water gathering properties when walking in humid environments.

Yeh, again I’m not sure how efficient using water is but my instinct says it will be a lot better than any mechanical system as they are generally very inefficient!

I’m going to preface this by saying, all I know is that know about the subject was one physics class in college… The teacher mentioned Hydro Pump Storage that pumps water into a reservoir when there is an excess of energy generation then releases it through turbines when there is a surge is energy needs on the grid. Wouldn’t this idea work in a very similar way? If so it would seem feasible as about 15% of the UKs STOR requirements are met in this way.

https://www.nationalgrid.com/sites/default/files/documents/STOR Fuel Type Analysis Summary (By Capacity) - Season 8.5 - Final_0.pdf

https://www.sse.com/news-and-views/2023/03/britain-s-largest-pumped-hydro-scheme-in-40-years-gets-100m-investment-boost/

This is why I try to make every moment special with them and give them the happiest life possible. It doesn’t make it hurt less, but you can know that you made one souls life as perfect as possible and you loved them with all your heart.

I also found a huge difference between filaments. Creality was terrible for me, Reflow is great

This really summarises the passive aggressive level you get to with a 3D printer: “Lift off the bed now you little fucker!”

So a combination of three changes finally got me back the correct result.

1. Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
2. Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
3. Reduced the temp by 10°C apart from the first layer.

Thanks for your help!

So a combination of three changes finally got me back the correct result.

1. Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
2. Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
3. Reduced the temp by 10°C apart from the first layer.

Thanks for your help!

So a combination of three changes finally got me back the correct result.

1. Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
2. Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
3. Reduced the temp by 10°C apart from the first layer.

Thanks for your help!

I will check that, I hope its that as that would be an easy fix. Also I only use matte filament.

When you say pressure of the z-axis, do you know what they meant exactly? Not sure it could be temp as it’s the same, however I did change the part cooling fan in case that was faulty and the material wasn’t cooling fast enough

Nice try robots! I’m not helping you learn how to fool us humans.

This one word made me laugh more than it had any right to.

Agreed. Give me the long lens/3 lenses on the mini form factor and that’s the sweet spot for me.

And those numbers could double as letters if you pressed them multiple times…

I still have this problem. The right side of the x axis is loose on the upright for me. Adding a dual z-axis didn’t help much, it still sacks sometimes. Next step is to add a cr-touch or completely rebuild. I’d also like to hear some other ideas for permanent fixes